Home > Cannot Connect > Vmware Clone Failed Cannot Connect To Host

Vmware Clone Failed Cannot Connect To Host

Contents

You may get a better answer to your question by starting a new discussion. Log into the console on the host and kill/backup the current vpxa.cfg file. # mv /etc/opt/vmware/vpxa/vpxa.cfg /etc/opt/vmware/vpxa/vpxa.zoldcfg (The above command backups the old file to a new one called vpxa.zoldcfg. Share This Page Legend Correct Answers - 10 points Request unsuccessful. Help Desk » Inventory » Monitor » Community » home design & development Lotus application developmentprint designweb site developmentmedia and publishingrequest a design quote solutions & consulting Notes and Domino application check my blog

Romeo said, February 11th, 2008 at 17:07 Had a similliar issue with the same error message when trying storage vmotion. Just want to know on which shelf in my brain I need to store this info on 😉 /Rubeck Duncan Epping says 19 September, 2008 at 12:22 esx 3.5 and vc This worked for me as well. 1. After verifying this was all good, I tried to reconfigure the host for VMware HA (to update the FT_HOSTS file, etc).

Relocate Virtual Machine Cannot Connect To Host

That leaves the question, "Did you recently change your ESXi host's IP address without a "Reset to Factory Defaults"? I added both hosts to the cluster again and every thing seemed to work again… until I decided to rollout a template. To leave the hidden console: 1. Done this to resolve the cloning issue: - Disconnect + Removed the Host from the cluster - moved the vpxa.cfg - Connect + Added the thost to the DRS/HA Cluster again

Talk about a fuster cluck. I am having trouble taking a clone of the VCENTER VM machine. rich Stephane says 18 September, 2008 at 16:31 Hi, I have the same issue. Deploy Template Cannot Connect To Host So I checked if I was able to clone via vmkfstools from the service console, this also worked.

Not that I have this issue, or ever even seen it….. Please type your message and try again. 4 Replies Latest reply: May 25, 2010 6:22 AM by ferreepa Attempting to Clone VM results in "Failed to connect to host" radman Feb You could argue that you should remove the host from vCenter, but if you put it in Maintenance mode, nothing is vMotioning to it and plus you won't lose any performance/statistical The task at hand was to cold migrate one of a Virtual Machine’s disks from it’s old LUN, to a new one with some more breathing room.

Thanks to post number 5 for the sample, my mssql needed something like UPDATE [VIM_VCDB].[dbo].[VPX_HOST] SET IP_ADDRESS =" WHERE DNS_NAME = N" Considering I only have 3 hosts I just opened Failed To Clone State For The Entity On Extension Vservice Manager That works a treat!! First put the esx in maint. Disconnect and remove the host from VC. - Select the host, right-click and choose "Disconnect". - Select the italic/grayed-out again, and this time, select "Remove".

Vcenter Cannot Contact The Specified Host

Vraag me af of het iets met SQL 2005 te maken heeft…. Restarting the Virtual Center Service. Relocate Virtual Machine Cannot Connect To Host They are at the bottom of these notes. Cannot Connect To Host Vmware Stopped the the virtual center service, updated the DB and started it back up.

Restart the management agents: ESXi: On the host, click the Customize System option. http://bovbjerg.net/cannot-connect/vmware-clone-error-cannot-connect-to-host.php Duncan Epping says 19 September, 2008 at 09:35 Your best bet would be the following: go to the console to see if the file /etc/opt/vmware/vpxa/vpxa.cfg is still there, remove it if Further info... David D. Cannot Synchronize Host Authenticity Of The Host's Ssl Certificate Is Not Verified

says 19 June, 2008 at 16:30 Thanks to all. Recommended Read! John P. news Greet Luuk sst says 5 May, 2009 at 15:34 Cudos to post 5 and 36… To preserve performance data, this method is preferred: Stopping the Virtual Center Service Editing the Virtual

hold down and click . Disconnected From Host. Reason Cannot Verify The Ssl Thumbprint I have finally found out the root password and connected directly to the ESXI host and now the clone option is not visible / available. i put the 2 hosts that i change the IP Address on in Maintenance mode and removed them from the VCenter and then added them back in and the DB as

Incapsula incident ID: 277000460008839708-13580098197586662 Request unsuccessful.

very odd. 0 This discussion has been inactive for over a year. Text Quote Post |Replace Attachment Add link Text to display: Where should this link go? I tried editing the file, but when ever I initiated a clone the hostIp was changed again to the old value. Vmware Host Disconnected From Vcenter For info I am running VMWare vCenter Server Version 4.1.0 and connecting with vSphere Client Version 4.1.0 Thanks Reply Subscribe RELATED TOPICS: Relocating vCenter Server Appliance VSphere 5.0 unable to migrate,

Once you restart the Virtual Center Service, the vpxa.cfg is updates properly. Any help would be greatly appreciated…. each time I try to "remove" the host from the list that is not in the cluster it shuts down my virtual center service, when I try and reconnect the one http://bovbjerg.net/cannot-connect/vmware-cannot-connect-to-host-during-clone.php It started to sound like the VCDB was over-writing any value for the Service Console IP because it had existed in it's DB and it's sort of proxying this self-DNS information

I have this error : "Unable to access the specified host. Login and choose the Restart Management Agents option. (Be careful not to click "Reset to Factory Defaults". Dolly says 24 November, 2008 at 19:24 Thanks Eric that helped stoz says 11 February, 2009 at 22:08 guys and girls, server one has ip from server to and vice versa When I connected via IP address, I was doing this in my troubleshooting, the host would quickly change from the host IP to the IP address of my primary site's gateway.